DSP-7LP - low power vehicle detector for solar powered safety loop installations.
DSP-7LP LOW POWER MULTI-VOLTAGE MICRODETECTOR
A new low power "Fail-safe" vehicle detector that is perfect for solar powered safety loop installations.
It is the low power version of our DSP-7 detector. It beats all competition for low current consumption.
Less than 1mA without a vehicle and approximately 23mA with a car on the loop. Like the DSP-7 and the DSP-6LP, it operates on any
voltage from 10 to 30 volts AC or DC.
DSP-6LP - low power vehicle detector for solar powered free exit loop installations.
DSP-6LP LOW POWER MULTI-VOLTAGE MICRODETECTOR
Our low power "Fail-secure" vehicle detector that is perfect for solar powered free exit loop installations.
This detector beats all competition for low current consumption.
Less than 1 mA without a vehicle, and approximately 23 mA with a car over the loop.
Just like the DSP-7 and the DSP-7LP, it operates on any voltage from 10 to 30 volts AC or DC.
DSP-22 - switchless two-channel vehicle detector for use with DoorKing Operators.
DSP-22 TWO CHANNEL DETECTOR FOR DOORKING OPERATOR
Another switchless two-channel vehicle detector product designed to work with the DoorKing operators.
This detector is available with a solid state presence output on channel 1 and a N.O. and a N.C. relay output on channel 2.
The channel 2 detector also has a switch to operate in either the pulse or presence mode.
DSP-11 - switchless, single output vehicle detectors with industry standard 11-pin base
DSP-11 MICRODETECTOR
A complete line of simple, switchless, single output vehicle detectors available with the industry standard 11-pin base.
Three models for your complete 11-pin vehicle detector needs: The DSP-11-LV will operate on any voltage with any polarity from 10 to 30 volts AC or DC.
The DSP-11-117 operates on 117 VAC lines. The DSP-11-230 operates on 230 VAC mains.
DSP-7 - vehicle detector for parking, drive-through and other access control applications
DSP-7 MICRODETECTOR
Our workhorse, the DSP-7 has set a new standard for access and parking detectors.
This vehicle detector is available with a NO and a NC relay output.
And of course, it works on any voltage between 7 and 30 volts - AC OR DC.
The DSP-7 "Fail-Safe" vehicle detector has been specifically designed to handle gates, parking,
drive-through and other access control applications.
DSP-40S - plug-in vehicle detector with solid-state outputs for detect and fail sensors.
DSP-40S PLUG-IN DETECTOR
The DSP-40S detector does have the flexibility of changing the sensitivity level if necessary. (See detailed specifications). This plug-in vehicle detector has been specifically designed to handle parking, drive-through and access control applications where solid-state outputs are required for both the "Detect" and the "Fail" outputs.
DSP-10 - vehicle detector for access control, drive-through, and parking, applications..
DSP-10 PARKING DETECTOR
The DSP-10 vehicle detector can be used on entrance loops, safety loops, or free exit loops.
Dual relay outputs, extension, delay, pulse on exit or entrance and the flexibility to be either "fail safe" or "fail secure".
The DSP-10 is available in 3 models. DSP-10-LV (10 to 30 Volts AC or DC) , DSP-10-117 (85 to 125 VAC), DSP-10-230 (180 to 250 VAC)
DSP-15 - pcb version vehicle detector for access control, drive-through, and parking.
DSP-15 PARKING DETECTOR
The DSP-15 vehicle detector is a PCB version of the DSP-10. This Low voltage detector will operate on any voltage AC or DC from 10 to 30 Volts and can be ordered with the terminal board connector option or a removable connector and harness.